![]() ![]() Materials to repack and return the unit to the supplier if needed. Possible, retain the carton, including the original packing materials. Inform your supplier if there are any incorrect, missing, or damaged parts. Installer(s) are required to record the antenna gain for this device in Responsible for ensuring that Equivalent Isotopically Radiated Power (EIRP) levels forĪll external antenna devices are compliant with the regulatory standards of the hostĬountry/domain. Technician using manufacturer-approved antennas only. Installers must orient the antennas with ANT0 and ANT2 at 45 degree angles and ANT1Īll Aruba devices with external antennas must be installed by an ACMP qualified The connectors are labeledĪNT0, ANT1, and ANT2, and correspond to radio chains 0, 1, and 2.įor optimal performance when using articulating direct-mount antennas, professional The AP-214 is equipped with three external antenna connectors. Refer to the Aruba Domain Regulatory Table at. For complete list of approved channels in your country, The network administrator(s) is/are responsible forĮnsuring that configuration and operation of this equipment is in compliance with Points are classified as radio transmission devices, and are subject to government Mobility Professional (ACMP) or similar Aruba-certified technician. This device must be professionally installed and serviced by a trained Aruba Certified ĎŹ Central management configuration and upgrades through a controller ĎŹ Compatibility with IEEE 802.3at PoE and 802.3af PoE ĎŹ IEEE 802.11a/b/g/n/ac operation as a wireless air monitor ĎŹ IEEE 802.11a/b/g/n/ac operation as a wireless access point ĎŹ Protocol-independent networking functionality The Aruba AP-210 Series access point provides the following capabilities: These ports have RJ-45įemale connectors with the pin-outs shown in Figure 6. The 10/100/1000 Mbps Ethernet ports are on the bottom of the AP. Once you have the above status “Disabled”, then the AP has successfully been upgraded.Figure 2 AP-210 Series Side View (AP-214 shown) To check when the upgrade has completed go to “Advanced Settings”Ĭlick “Refresh” until the “Debug” status shows “Disabled” – NOTE: The AP will disappear from the above list… the AP is in “Reboot” Mode and will return. Step 9 – Due to this is a SSH connection and not Console, the session you have with PuTTy will have terminated and no screen feedback will be shown on the progress. You should see the following screen to illustrate the tftp transfer is in progress You need to enter the FULL file with extension: Once you have successfully logged in, type the following command: Step 8 – You should be prompted to login as follows: Step 7 – Once the “Debug” status shows “Enabled” then open PuTTY and configure as follows: You will also need to remember the IP Address Step 6 – Click the link against the MAC address you want to manually upgrade under “Debug”Ĭlick “Enabled” then enter the password – In this example we have used “admin” as the password. WLAN > Administration > AP Management > Advanced Settings Step 5 – Change AP status to “Debug Mode” – You will need to identify the MAC address of the problematic AP You should be prompted with the login page – Login with your details (Our example was: admin and password: admin) In our example we have used the IP address of 192.168.1.161 Step 4 – Enter the web GUI interface of the DWS-3160-24PC using its IP address in a web browser. Step 3 – Transfer the firmware downloaded and place into the “Current Directory” Server interfaces: 192.168.1.136 (This is the IP address to where the tftp server resides) Step 2 – Install and configure tftp server as follows:Ĭurrent Directory: C:\Program Files\Tftpd32 Step 1 – Download the firmware for the AP – In our example we have used the DLW-8610AP NOTE: This is a procedure in case upgrading via switch is unsuccesfulġ) FW: DWL-8610_FW_v_4.3.0.2_B053.tar (Please always check our website for new release)ģ) Tftp Server (Install the “Standard Editiion” – depending on plataform 32 or 64 bit) ![]()
0 Comments
Leave a Reply. |
Details
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |